Vaisala DMP248 Manuel de service Page 4
- Page / 145
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
OPERATING MANUAL_______________________________________________________________
II_______________________________________________________________________ U263EN-1.4
S
ERIAL COMMANDS........................................................................................................................................... 46
Auto-calibration........................................................................................................................................... 46
Pressure compensation ................................................................................................................................ 48
Analogue outputs......................................................................................................................................... 49
Setting the analogue outputs .....................................................................................................................................49
Selecting and scaling the analogue output quantities ................................................................................................49
Scaling the analogue outputs.....................................................................................................................................50
Output via the serial bus .............................................................................................................................. 50
Starting the measurement output...............................................................................................................................50
Stopping the measurement output.............................................................................................................................51
Outputting the reading once ......................................................................................................................................51
Setting the output interval for the RUN mode...........................................................................................................51
Serial bus settings......................................................................................................................................................52
Selecting the output units..........................................................................................................................................52
Setting the transmitter address ..................................................................................................................................52
Resetting the transmitter............................................................................................................................................53
Operating the transmitter via the serial bus ................................................................................................. 53
Setting the serial interface.........................................................................................................................................53
OPEN & CLOSE ......................................................................................................................................................53
CHAPTER 6 CALIBRATION .......................................................................................................................... 55
H
UMIDITY CALIBRATION................................................................................................................................... 55
Two-point calibration procedure ................................................................................................................. 56
Using serial commands .............................................................................................................................................56
Using display/keypad commands..............................................................................................................................57
Using LED commands..............................................................................................................................................57
Humidity calibration table........................................................................................................................... 59
T
EMPERATURE CALIBRATION............................................................................................................................ 59
One point offset correction.......................................................................................................................... 59
Using serial commands .............................................................................................................................................59
Using display/keypad commands..............................................................................................................................60
Using LED commands..............................................................................................................................................60
Two-point temperature calibration .............................................................................................................. 61
Using serial commands .............................................................................................................................................61
Using display/keypad commands..............................................................................................................................62
Using LED commands..............................................................................................................................................62
CALIBRATION OF THE ANALOGUE OUTPUTS ...................................................................................................... 63
Using serial commands................................................................................................................................ 63
Using display/keypad commands ................................................................................................................ 63
Using LED commands................................................................................................................................. 64
CHAPTER 7 MAINTENANCE ........................................................................................................................ 67
R
EFERENCE MEASUREMENTS ............................................................................................................................ 67
S
ELF-DIAGNOSTICS ........................................................................................................................................... 67
T
EMPERATURE CHANNEL ADJUSTMENT WITH PT 100 SIMULATORS .................................................................. 68
Adjustment using serial commands............................................................................................................. 69
Adjustment using display commands .......................................................................................................... 69
Adjustment using LED commands.............................................................................................................. 69
M
EASUREMENT OF OUTPUT CURRENTS USING TEST POINTS............................................................................... 70
A
DJUSTING THE CONTRAST OF THE DISPLAY ..................................................................................................... 71
CHAPTER 8 TECHNICAL DATA .................................................................................................................. 73
M
EASURED VARIABLES..................................................................................................................................... 73
Dewpoint temperature ................................................................................................................................. 73
Temperature................................................................................................................................................. 74
Relative humidity ........................................................................................................................................ 74
Ppm volume concentration (dry) ................................................................................................................. 74
O
UTPUTS........................................................................................................................................................... 74
- OPERATING 1
- Table of contents 3
- GENERAL INFORMATION 7
- PRODUCT DESCRIPTION 9
- FIGURE 2-2 shows the DRYCAP 11
- FIGURE 2-1. Now the RH 11
- Use in high pressure 12
- INSTALLATION 13
- PROBE UP 14
- DOWN 14
- Mounting; overview 15
- FIGURE 3-7 17
- R1/2 ISO 7/1 20
- VALVE OPEN 21
- PRESS TOOL 21
- VALVE CLOSED 21
- Sample cell 24
- SAMPLE CELL 25
- Grounding 27
- Connections 29
- Connection to an AC supply 30
- COMMISSIONING 31
- FIGURE 4-2 32
- RXWSXWVÕ6FDOH 33
- Spare jumpers 33
- COMMANDS 39
- LED commands 40
- Display/keypad commands 41
- Auto-calibration 42
- Forced auto-calibration 44
- Analogue output commands 44
- FIGURE 4-2) 45
- Output via serial bus 46
- Output modes 48
- Pressure compensation 50
- Setting the date 51
- Setting the time 51
- Serial commands 52
- Analogue outputs 55
- Output via the serial bus 56
- Outputting the reading once 57
- Serial bus settings 58
- Selecting the output units 58
- Resetting the transmitter 59
- Setting the serial interface 59
- OPEN & CLOSE 59
- 2 which is in POLL state 60
- CALIBRATION 61
- Using serial commands 62
- Using display/keypad commands 63
- Using LED commands 63
- Temperature calibration 65
- MAINTENANCE 73
- Adjustment using LED commands 75
- TECHNICAL DATA 79
- Temperature 80
- Relative humidity 80
- Electronics 82
- Serial interface modules 82
- Electromagnetic compatibility 83
- CHAPTER 9 OPTIONS 84
- SPARE PARTS AND 85
- ACCESSORIES 85
- APPENDIX 1 SERIAL COMMANDS 87
- Auto-calibration commands 89
- Calibration commands 93
- : 0.000 94
- FTIME Adding time to output 99
- FDATE Adding date to output 100
- SERI Serial bus settings 101
- Operation modes 103
- DATE Setting the date 106
- TIME Setting the time 107
- ?? <cr> 108
- APPENDIX 2 109
- Power supply module 110
- Technical specifications 111
- APPENDIX 3 113
- Installation 114
- Operation 114
- Network configuration 116
- RX GND TX 117
- Dual loop operation 118
- STOP mode 120
- POLL mode 121
- Specifications 122
- APPENDIX 4 123
- Dual loop wiring 129
- Current loop settings 131
- APPENDIX 5 133
- Errors after reset 134
- Errors during operation 135
- APPENDIX 6 137
- APPENDIX 7 139
- APPENDIX 8 145
Produits connexes et manuels pour Mesure, test et contrôle Vaisala DMP248
(71 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels