Vaisala BAROCAP PTB330 Guide de l'utilisateur Page 110
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
User's Guide ______________________________________________________________________
108 _________________________________________________________________ M210855EN-C
Opening and Closing the Adjustment Mode
The adjustment mode has to be available before you can proceed with
the adjustment and calibration. The adjustment button with indicator
LED is located in the upper corner on the left-hand side of the
motherboard. See the position of the adjustment button in Figure 2 on
page 20.
1. Open the barometer cover.
2. Press the ADJ button. The adjustment mode is now available. The
red indicator LED is on.
3. Press the ADJ button again to lock the adjustment mode. The red
indicator LED is off.
The adjustment menu on the display/keypad is visible only when the
ADJ button (on the motherboard inside the transmitter) is pressed.
NOTE
Entering new linear or multipoint corrections will always cancel the
previous corrections. It is advisable to write down the previous linear
and multipoint corrections so that they will not be lost by mistake.
Table 15 Adjustment and Calibration Commands for
Barometer Module P1
Command Function
LCP1 ON/OFF Enables/Disables the linear
corrections
LCP1 Enter linear corrections
MPCP1 ON/OFF Enables/Disables the multipoint
corrections
MPCP1 Enters multipoint corrections
CDATE Shows or sets the calibration date
CTEXT Shows or sets the calibration info
text.
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 4 4
- CHAPTER 5 6
- CHAPTER 6 6
- CHAPTER 7 6
- APPENDIX A 7
- APPENDIX B 7
- APPENDIX C 7
- List of Figures 9
- List of Tables 11
- GENERAL INFORMATION 13
- General Safety Considerations 14
- Feedback 14
- ESD Protection 15
- Recycling 16
- Trademarks 16
- License Agreement 16
- Warranty 17
- PRODUCT OVERVIEW 19
- Pressure Measurement 20
- 0705-091 22
- 0508-019 24
- 0503-004 24
- 0503-006 26
- Mounting Rain Shield with 28
- Installation Kit 28
- Panel Mounting Frame 29
- Cable Bushings 30
- 0604-059 31
- Alternate Wiring Systems 33
- 0703-019 34
- M-12 (8-Pin) Connector 36
- D-9 Connector 37
- AC Power Supply Module 38
- Installation 39
- Warnings 40
- Galvanic Isolation for Output 43
- Analog Output Module 44
- Relay Module (RELAY-1) 45
- 0503-037 47
- Figure 26 4-Wire RS-485 Bus 50
- Table 5 4-Wire (Switch 3:On) 50
- Figure 27 2-Wire RS-485 Bus 51
- OPERATION 53
- Menus and Navigation 54
- Reading 55
- 0708-035 56
- 0703-033 58
- Display Settings 60
- Rounding 61
- Backlight 61
- Contrast 61
- Keypad Lock 61
- Measuring Settings 62
- Diagnostic Settings 62
- Serial Interface Settings 63
- System Settings 64
- Factory Settings 65
- Clearing Graph Displays 65
- Relay Settings 66
- Analog Output Settings 68
- Serial Line Communication 70
- User Port Connection 71
- 1 2 3 4 5 72
- Service Port Connection 73
- Terminal Program Settings 73
- 0507-028 74
- 0507-027 74
- General Settings 78
- Changing Quantities and Units 78
- Measurement Related Commands 81
- User Port Serial Settings 83
- System Information Commands 85
- Resetting barometer By Using 86
- Serial Line 86
- Locking Menu/Keypad by Using 87
- Data Recording 88
- Selecting Data Recording 88
- Quantities 88
- View Recorded Data 89
- DELETE/UNDELETE 90
- Operation of Relays 91
- Quantity For Relay Output 91
- Hysteresis 92
- Enabling/Disabling Relays 94
- Setting Relay Outputs 95
- Testing Operation Of Relays 96
- Operation of RS-485 Module 97
- Networking Commands 97
- >INTV 10 min 99
- Output interval: 10 min 99
- Operation of Analog Output 101
- 0705-211 102
- 0706-031 102
- Analog Output Tests 104
- Periodic Maintenance 105
- Cleaning 105
- Error States 105
- 0706-070 106
- Pressure 109
- Pressure Adjustment 111
- Using Display/Keypad 116
- Using Serial Line 116
- Specifications 119
- Performance 119
- Operating Environment 120
- Inputs and outputs 121
- Mechanics 122
- Technical Specifications of 122
- Optional Modules 122
- Table 26 Relay Module 123
- Table 27 RS-485 Module 123
- Options and Accessories 124
- Dimensions (in mm) 125
- Technical Support 125
- Return Instructions 126
- Vaisala Service Centers 127
- CALCULATION FORMULAS 129
- 0706-110 130
- 0706-111 130
- Min...Max 132
- PA11A EMULATION MODE 135
- PA11A Message Format 136
Produits connexes et manuels pour Mesure, test et contrôle Vaisala BAROCAP PTB330
(206 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels