Vaisala BAROCAP PTB330 Guide de l'utilisateur Page 112
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
User's Guide ______________________________________________________________________
110 _________________________________________________________________ M210855EN-C
Adjustments Using Display/Keypad
Use the display/keypad to view the active multipoint/linear
adjustments.
1. Press the ADJ button located on the motherboard in the upper
corner on the left-hand side to open the ADJUST PTB330 menu.
2. Select P1 adjustments, press the right arrow button.
3. Select Multipoint /Linear adjustment. If the corresponding
adjustment is already enabled, it is marked with a check mark.
4. If the adjustment is enabled, press the SHOW button to see the
active adjustment values. Press OK to leave the adjustment active
or DISABLE to disable the adjustment (confirm by pressing
YES).
5. Press the left arrow key to go back to the ADJUST PTB330 menu.
6. Exit the adjustment mode by pressing EXIT.
To measure new adjustment values and perform the actual adjustment,
first disable the corresponding adjustment on each barometer module
you are going to adjust (see the procedure above). If you are going to
perform a multipoint adjustment, disable also the linear adjustments. If
you are going to do only a linear adjustment, leave the multipoint
adjustments untouched.
After disabling the previous adjustments, calibrate the PTB330 against
your pressure reference. Make a note of the pressure reading of each
PTB330 barometer module separately (quantities P
1
, P
2
, and P
3
). Then
use the display/keypad to enter and activate the new multipoint/linear
adjustment factors.
1. Press the ADJ button located on the motherboard in the upper
corner on the left-hand side to open the ADJUST PTB330 menu.
2. Select P1 adjustments, press the right arrow button.
3. Select Multipoint /Linear adjustment, press the SET button.
4. Select an existing adjustment point or Add adjustment point and
press the SET button to enter your new values. If asked, select
MODIFY to replace the old values with your new ones.
5. Enter the P
1
value of the PTB330 at the Reading prompt using the
up/down arrow buttons. Press the OK button.
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 4 4
- CHAPTER 5 6
- CHAPTER 6 6
- CHAPTER 7 6
- APPENDIX A 7
- APPENDIX B 7
- APPENDIX C 7
- List of Figures 9
- List of Tables 11
- GENERAL INFORMATION 13
- General Safety Considerations 14
- Feedback 14
- ESD Protection 15
- Recycling 16
- Trademarks 16
- License Agreement 16
- Warranty 17
- PRODUCT OVERVIEW 19
- Pressure Measurement 20
- 0705-091 22
- 0508-019 24
- 0503-004 24
- 0503-006 26
- Mounting Rain Shield with 28
- Installation Kit 28
- Panel Mounting Frame 29
- Cable Bushings 30
- 0604-059 31
- Alternate Wiring Systems 33
- 0703-019 34
- M-12 (8-Pin) Connector 36
- D-9 Connector 37
- AC Power Supply Module 38
- Installation 39
- Warnings 40
- Galvanic Isolation for Output 43
- Analog Output Module 44
- Relay Module (RELAY-1) 45
- 0503-037 47
- Figure 26 4-Wire RS-485 Bus 50
- Table 5 4-Wire (Switch 3:On) 50
- Figure 27 2-Wire RS-485 Bus 51
- OPERATION 53
- Menus and Navigation 54
- Reading 55
- 0708-035 56
- 0703-033 58
- Display Settings 60
- Rounding 61
- Backlight 61
- Contrast 61
- Keypad Lock 61
- Measuring Settings 62
- Diagnostic Settings 62
- Serial Interface Settings 63
- System Settings 64
- Factory Settings 65
- Clearing Graph Displays 65
- Relay Settings 66
- Analog Output Settings 68
- Serial Line Communication 70
- User Port Connection 71
- 1 2 3 4 5 72
- Service Port Connection 73
- Terminal Program Settings 73
- 0507-028 74
- 0507-027 74
- General Settings 78
- Changing Quantities and Units 78
- Measurement Related Commands 81
- User Port Serial Settings 83
- System Information Commands 85
- Resetting barometer By Using 86
- Serial Line 86
- Locking Menu/Keypad by Using 87
- Data Recording 88
- Selecting Data Recording 88
- Quantities 88
- View Recorded Data 89
- DELETE/UNDELETE 90
- Operation of Relays 91
- Quantity For Relay Output 91
- Hysteresis 92
- Enabling/Disabling Relays 94
- Setting Relay Outputs 95
- Testing Operation Of Relays 96
- Operation of RS-485 Module 97
- Networking Commands 97
- >INTV 10 min 99
- Output interval: 10 min 99
- Operation of Analog Output 101
- 0705-211 102
- 0706-031 102
- Analog Output Tests 104
- Periodic Maintenance 105
- Cleaning 105
- Error States 105
- 0706-070 106
- Pressure 109
- Pressure Adjustment 111
- Using Display/Keypad 116
- Using Serial Line 116
- Specifications 119
- Performance 119
- Operating Environment 120
- Inputs and outputs 121
- Mechanics 122
- Technical Specifications of 122
- Optional Modules 122
- Table 26 Relay Module 123
- Table 27 RS-485 Module 123
- Options and Accessories 124
- Dimensions (in mm) 125
- Technical Support 125
- Return Instructions 126
- Vaisala Service Centers 127
- CALCULATION FORMULAS 129
- 0706-110 130
- 0706-111 130
- Min...Max 132
- PA11A EMULATION MODE 135
- PA11A Message Format 136
Produits connexes et manuels pour Mesure, test et contrôle Vaisala BAROCAP PTB330
(206 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels